- Free cosplay foam templates pdf#
- Free cosplay foam templates download#
- Free cosplay foam templates free#
I used a metallic gold spray paint on this, no primer and no sanding. For this, I got the scraps very hot, rolled them into a line, reheated that and then wrapped it around the base of the horns. I save ALL my Worbla scraps because they are great for small details like this. The cool thing about Worbla is that you can use every bit of it, and also reuse it even after you’ve shaped it. I used a few Worbla scraps and heated them up, rolled them into a snake and wrapped them around the horns base to make sure they were securely attached to the helmet. When the horns are ready, you can attach them with hot glue or your preferred adhesive. Let it sit for a bit after taking it out of the oven because it will be hot. It would take longer for larger or thicker horns. Sculpey bakes at 275 degrees for 15 minutes for smaller pieces. ) The way I made sure they were equal in size was to line them up in a heart shape.Įither bake your horns if using Sculpey, or let them dry and harden if using a different type clay. (Just ignore the two smaller rolled pieces in the photo. You can go big or small! Horn size is all up to your own preference. Roll it into a ball to get it smooth, then roll it into a snake and taper one end. To make the horns equal, just cut off equal parts of modeling compound before you start molding. I used Sculpey III for this, but you can use any modeling compound. If using elastic, you can attach the elastic to the sides with glue. I do this by covering the headband in hot glue, putting it on my head, and then sticking on the helmet piece. Once you have the helmet shaped, hot glue it to the headband. Step 6: Attach it to your headband (or elastic) The reason I didn’t stick it on before shaping it is because I was worried the top pieces would get too floppy when heating it the second time. You can do the Foam/Worbla combo for this piece if you want more dimension. Once you have it curved, heat the smaller piece and stick it to the big piece. If using Worbla, you can heat it up and stick it on. Once you’ve bonded the two pieces together, heat it up again and bend it around your head while wearing the headband. Step 4: Heat Worbla/Foam combo and form around head Press down a little extra around all the edges to seal it. Use something with a straight edge, like a credit card, to drag across the surface and get out all the air bubbles. If you are doing the Worbla/Foam combo, heat the Worbla up using a heat gun and lie it on top of the craft foam. Step 3: Cover craft foam with Worbla while it is flat The black Worbla is smoother than the tan, so I usually use the black if I have it. If using the Worbla, it makes it so it is ready to paint. You can actually just make this only using the foam as long as you prime it before painting. I use a combo of thin craft foam with Worbla on top, because it makes it nice and solid. I used craft foam as the base, with Worbla on top. Step 2: Trace paper template onto your preferred medium. Depending on your margins, it may say part of it is out of the printable area. When you print, make sure you change your layout to landscape.
Free cosplay foam templates download#
You’ll want to download it from there and not just right click the picture here or it won’t be the right size.
Free cosplay foam templates free#
Let’s get started! First you’ll need the template: Click here for the Free Loki Helmet Template DownloadĬlick the pic or the link to download the. I know Denji will be a fan favorite and Chainsaw Man Cosplays will be everywhere.Loki Helmet Template Step 1: Print the template on paper and cut it out. For those that don't know Chainsaw Man is an amazing over the top gory manga that is currently be made into an anime. Because of that some details might not be 100% but it's definitely good enough for cosplay and worse case you can make up your own details. I took some liberties myself with the back of the head because it is never fully shown in the trailer and varies panel to panel in the manga. This Chainsaw Man cosplay is based off of the manga and the Anime PV trailer. In Part 2 I will cover the acrylic painting and weathering processes including epoxy gore. This Chainsaw Man helmet is made almost entirely out of EVA HD Foam and because of that it weighs in at an amazing 1 pound 10 ounces! In this Part 1 video I go through all of the fabrication steps needed to create the cosplay helmet.
Free cosplay foam templates pdf#
How to Make Chainsaw Man Cosplay helmet with Free PDF Templates! In this Part 1 video I will go over all of the steps I took to create this Chainsaw Man / Denji Cosplay and by downloading the free PDF templates from my site you can build it right along with me.